How Do I Repair A Small Chip In My Pergo Outlast Flooring

Download Commodity

Pergo is a brand of health conscious laminate that's like shooting fish in a barrel to construct and durable to use. The Pergo installation procedure makes a cakewalk of weekend projects for do-it-yourselfers. Though not recommended to be used in mobile homes or on boats and planes, Pergo flooring can be installed in your home in any room, over wood or physical sub-floors.

1
Prepare the flooring. Clean any droppings off the floor and secure any loose floorboards earlier attempting to install anything over the sub-floor. Brand sure the sub floor is level with a carpenter'south level. Flooring leveling is unremarkably but washed on concrete floors, only you tin find speckling product at the store that y'all tin employ with large putty knives, if you've got a few spaces out of alignment. You tin can besides but install Pergo over the floor, fifty-fifty if it'due south a chip uneven, simply you risk peachy or separating the tiles eventually.^[one]
- If you're remodeling and not installing Pergo in a new installation, remove any carpet, padding and remnants from the flooring. Remove baseboards, vent covers, and whatever other fixture that would present an obstruction to the flooring. You lot should clear all the mode to the sub-floor.
- If you lot need to undercut the baseboard, use an undercut saw with plastic spacers. Saw the bottom of the trim or flake it out using a chisel or utility pocketknife. It should pop off hands.
2
Install the vapor barrier. Whether y'all're installing Pergo over concrete or woods floors, it's common to install a vapor barrier if y'all're concerned about moisture. Laying a laminate vapor bulwark helps to keep wet from going into the fiberboard and causing information technology to warp. This should be available in the flooring section of whatever home repair shop.^[2]
- Lay the underlayment in strips so they are touching but non overlapping. Any overlap will crusade uneven spots in the flooring, so try to shine it out equally much equally possible.
Advertisement
3
Choice a corner to start laying the Pergo. For most projects, you desire to showtime with the back left corner of the room and work toward the door. If yous commencement in the middle, you'll have to make cuts when you get to the edges, to brand the tiles fit.^[3]
- To install the tiles, remove the tongue from the first piece. This side volition face the wall. Place the tongue side of the 2d plank into the groove of the first, starting at an angle. When the tongue is in the groove, press down until the joint clicks into place. Work in rows. When you are done with the first row, motion to the next.
- Be sure to leave a consistent ane/four inch (0.635 cm) gap effectually all the edges of the room to allow for expansion with temperature changes. It's too common practice to lay the planks in the management that any lite inbound the room shines down the length of the plank.
4

Go along the row. At a 30 degree bending forth the long side of the 2 pieces, button the new slice into the groove. They should click together easily, or y'all tin can utilise a crowbar or a hammer to tap them into place gently.^[4]
v
Showtime the next row. Stagger the length of the planks in the second and post-obit rows so that none of the planks stop at the same place. The best way to practice this is to cut a two pes (0.61 m) (60.96 cm) length of plank and start the second row with it. And so use a full plank for the tertiary row and keep rotating across the room. Cutting your pieces in an area away from where you are installing the floor so the dust does not become into the joints.^[5]
- There are ever unfinished pieces that stick out effectually two to three sides. Measure from the end of the terminal piece, subtract a quarter inch, and mensurate the finished surface to that dimension. Make your cut using a mitre sliding saw. If information technology'southward non quite direct on the edges, information technology'll be covered by the baseboard anyway.
6

Continue laying rows until y'all've filled the room. Connect the joints of the long side of the starter piece with the groove of the last row laid. Press the plank down until it locks into place. Secure the slice into place by using a tapping cake almost the cease of the plank and gently knocking the slice. Keep with the tapping block downward the row as y'all place a plank.^[half-dozen]
vii

Install the baseboard . When yous've completed the rows, you're done with the Pergo installation. Install the baseboard according to your plans for the room and return any fixtures where yous removed them.

Advertisement

ane

Check to make sure the concrete is level. If you're laying Pergo over concrete, remove all carpet, trim, and other things covering the sub-flooring to betrayal the physical underneath. Earlier laying Pergo, information technology'south a good idea to shine out the concrete to make sure that you've got the flattest surface possible for the new installation. Apply the level to make certain it's smooth, and have steps to smooth it out if necessary with new concrete.^[7]
2
Mix a batch of concrete leveler. Uneven floors need to be smoothed out with concrete leveler. This usually comes in a forty-50lb bag, which can be mixed with water to gear up. In a bucket, mix a pocket-sized batch of concrete with h2o equally directed. Don't mix more you'll use in the next hour, or it'll dry out and become useless and hard.^[viii]
- Beginning at the everyman points in the room and pour a small reservoir, and then you can mix h2o in and wet the physical support if necessary. Use a putty pocketknife or a trowel to smooth out the physical as thinly every bit possible, feathering out the edges of your work as you go.
three

Install the vapor barrier when the concrete has dried. Wait at to the lowest degree 48 hours before installing a vapor barrier over the fresh concrete leveling job, then put down a vapor barrier every bit described previously. These polyurethane sheets are commonly available from Pergo dealers equally part of the package. Cover the entire floor with the sheets, which should be cut to completely comprehend the floor. Make it large enough on the sides so whatsoever vapor coming up will end up backside the baseboard. Tape the seams together earlier continuing with installation.^[9]
4

Install Pergo every bit before. In one case you lot've smoothed out the concrete and added the vapor barrier, installing Pergo over concrete should exist exactly the same equally installing over woods. Option a corner, start clicking them together leaving the appropriate amount of infinite between rows, and trim them to fit on the ends.

Advertisement

Add New Question

Question

What if my floor is sticky from removing stick-on tile?

Remove merely enough so that you can put in some of the undelayment. Remove plenty to do 1 column or row, then repeat the process. Yep, it's tiresome, simply whatever other way is messy and you may ruin some of your floor.
Question

On concrete floors can y'all use polyethylene before the pergo foam vapor barrier?

Yep you are supposed to. They should sell behemothic roles of visqueen (your polyethylene) at the domicile stores. I like 6mil just 4 is ok (thinner than half dozen).
Question

If I accept an fastened underlayment, exercise I need boosted underlayment?

Y'all should non apply additional underlayment. Including an additional layer of underlayment will probable void the warranty.
Question

Do I have to caulk around the perimeter of a new floor?

Yous don't take to, but information technology'due south a proficient idea, because it's like shooting fish in a barrel for spills to get though that fashion. You desire to seal any spots where water can get through, especially in kitchens.
Question

If a mistake is made after snapping a panel, can I unlock it?

Yes, you but need to agree down the i side it's attached to and lift up on the slice you want to remove.
Question

Do I demand to lay underlayment if I accept a subfloor already?

Yes. The underlayment provides a buffer and accounts for imperfections in the subfloor. (3mm works best.)
Question

Tin I install the flooring under my cabinets?

Yep, but you will need to remove the cabinets, and and then reinstall them on top of the floor.
Question

Our laminate is curling as we install each piece of Prego floor, making it impossible to keep adding rows. What can nosotros do?

Curling happens when the floor isn't locking correctly. Tap your planks tighter with a borer block (it is best to do this 1 at at time), since your floor isn't quite locked. This should help prevent the crimper.
Question

What should I do if the boards won't snap in?

Use a tapping block and pull bar where the block won't fit, and advisedly close the gaps keeping eight" from the edge of the plank. Lock either the curt end or the long edge commencement, then tap the other into place. The planks will flatten out as they are locked. Lifting the long side slightly (i") will help direct the plank into place if you've locked the short terminate first. The edges chip easily, then make certain your block is positioned correctly.
Question

Tin can I leave the baseboard on when installing over hardwood and only remove the quarter circular?

Yes, you tin can. What yous have described is a base of operations shoe or quarter round over a base lath. Treat the base shoe as baseboard and leave the existing baseboard in place. Reinstall the base shoe over the flooring which is installed up the border of the existing baseboard. Much easier than removing all. This besides an culling to removing a single existing baseboard, where you may install a base of operations shoe or quarter round over the flooring cutting and installed afterward.

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Video

Cut the Pergo floor with the confront side downwardly to help keep edges smooth.

Cheers for submitting a tip for review!

Things You'll Demand

Pergo flooring
underlayment
measuring tape
saw
1/four inch spacers (if needed)

Almost This Article

Article Summary 10

To install Pergo flooring, start by covering the flooring with with vapor barrier sheets all the way to the walls and taping whatever seams. Then, starting in the far corner of the room, lay the showtime tile downwards against the wall, removing the tongue so information technology's flush with the wall. And then, fit the tongue on the side by side plank into the groove of the first one and press down until information technology clicks into place. As you lay the tiles, stagger the length of the planks so that none of them cease in the same place. In one case you've covered the floor, install baseboards around the edges of the room. For tips on how to level a physical floor before installing Pergo flooring, read on!

Did this summary help you?

Thank you to all authors for creating a page that has been read 212,494 times.

Did this commodity assistance you?